![\"\"](\"https:\/\/www.bing-ri.com\/wp-content\/uploads\/SCI1608S2.png\")
<\/p>\nFeatures & Application
\n\u2022 Higher Q and lower DCR than other 0603 inductors
\n“\u2022 Very high SRF values \u2013 as high as 6.x GHz”
\n\u2022 Excellent current handling capability \u2013 up to 700 mA
\n\u2022 50 inductance values from 1.6 to 560 nH
\nCore material Ceramic
\nEnvironmental RoHS compliant, halogen free
\nTerminations Silver-palladium-platinum-glass frit. Other terminations
\navailable at additional cost.
\nAmbient temperature \u201340\u00b0C to +125\u00b0C with Irms current
\nMaximum part temperature +140\u00b0C (ambient + temp rise).
\nStorage temperature Component: \u201340\u00b0C to +140\u00b0C. Tape and reel packaging: \u201340\u00b0C to +80\u00b0C
\n“Resistance to soldering heat Max three 40 second reflows at +260\u00b0C,
\nparts cooled to room temperature between cycles”
\nTemperature Coefficient of Inductance (TCL) +25 to +125 ppm\/\u00b0C
\nMoisture Sensitivity Level (MSL) 1 (unlimited floor life at <30\u00b0C \/ 85% relative humidity)<\/p>\n
<\/p>\n
![\"\"](\"https:\/\/www.bing-ri.com\/wp-content\/uploads\/SCI1608S3.png\")
<\/p>\n
Impedance\/Inductance\/Q\/ LCR Angilent E4991A
\nResistance DC Chroma 16502
\nCurrent per winding that causes a 20\u00b0C rise from 25\u00b0C ambient
\nElectrical specifications at 25\u00b0C
\nWeight 4.2 \u2013 7.3 mg.
\nPackaging 2000\/7\u2033 reel; Plastic tape: 8 mm wide.
\nPackaging will different,accroding the various chip size.<\/p>\n
Typical Inductance vs Frequency<\/strong> Lead-free the recommended reflow condition<\/p>\n
\n![\"\"](\"https:\/\/www.bing-ri.com\/wp-content\/uploads\/SCI1608S4.png\")
\nGENERAL CHARACTERISTICS
\n1. Operating temperature range: -40 TO + 125\u2103(Includes temperature when the coil is heated)
\n2. External appearance: On visual inspection, the coil has no external defects.
\n3. Terminal strength: After soldering. Between copper plate and terminals of coil. Push in two directions of X.Ywithstanding at below conditions. Terminal should not peel off. (refer to figure at right) 0.5kg Min \u20131608
\n4. Insulating resistance: Over 100M\u2126 at 100V D.C. between coil and core
\n5. Dielectric strength: No dielectric breakdown at 100V D.C. for 1 minute between coil and core
\n6. Temperature characteristics: Inductance coefficient (0~2,000)x10-6\/ ( \u2103 -25~+80 ). \u2103 , inductance deviation within\u00b15.0%, after 96 hours.
\n7. Humidity characteristics(Moisture Resistance): Inductance deviation within \u00b15%, after 96 hours in 90~95% relative humidity at 40 \u00b12 and 1 hour drying under normal condition.
\n8. Vibration resistance: Inductance deviation within \u00b15%, after vibration for 1 hour. In each of three orientations at sweep vibration (10~55~10 Hz) with 1.5mm P-P amplitudes.
\n9. Shock resistance: Inductance deviation within \u00b15%, after being dropped once with 981m\/s2 (100G) shock attitude upon a rubber block method shock testing machine, in three different orientations.
\n10. Resistance to Soldering Heat: 260 , 10 seconds(See attached recommend reflow)
\n11. Storage environment: Storage condition: Temperature Range: 10 ~ 35 (Generally: 21 ~ 31 ) , Humidity Range: 50% ~ 80% RH (Generally: 65% ~ 75%) ; Transportation condition: Temperature Range:-35 ~ 85 , Humidity Range: 50% ~ 95% RH
\n12. Use components within 12 months. If 12 months or more have elapsed, check soldarability before use.
\n13. Reflow profile recommend:
\nLead-free heat en duran ce test<\/p>\n![\"\"](\"https:\/\/www.bing-ri.com\/wp-content\/uploads\/SCI1608S5.png\")
<\/p>\n![\"\"](\"https:\/\/www.bing-ri.com\/wp-content\/uploads\/SCI1608S6.png\")
<\/p>\n","protected":false},"excerpt":{"rendered":"